|
|
| (13711 intermediate revisions not shown) |
| Line 1: |
Line 1: |
| - | You've had a fire. The fire division has come, put the fire out and all you see is one particular large mess. Upon closer investigation questions come.
| |
| | | | |
| - | I. What strategy do we use to take away the soot and charcoal to evaluate the damage?
| |
| - |
| |
| - | - High pressure water blasting leaves behind water in electrical elements, gear and insulation, if not effectively removed will lead to unwanted corrosion and rot, rising cleanup, damage and extended phrase maintenance fees.
| |
| - |
| |
| - | - Soda blasting leaves water and soda behind, which requires additional cleanup, increasing cleanup, damage and long term upkeep fees.
| |
| - |
| |
| - | - Sand blasting leaves abrasive blast media behind, which if not cleaned up correctly continues to lead to damage in electrical components, gears and bearings. It continues to fall from horizontal surfaces, cracks and beams years following the job is carried out, increasing cleanup, damage and lengthy term
| |
| - |
| |
| - | upkeep charges.
| |
| - |
| |
| - | - Dry ice blasting is the ultimate surface cleaning procedure, it leaves no secondary waste stream behind. The only cleanup immediately after the dry ice blasting job is carried out is the removal of the debris triggered by the fire.
| |
| - |
| |
| - | II. How do we eliminate the soot, charcoal and smoke film from masonry and steel surfaces?
| |
| - |
| |
| - | - Yet again this is an outstanding application for dry ice blasting. Watch the film clips on our internet site to see how dry ice blasting cleans soot, smoke and charcoal from diverse types of surfaces.
| |
| - |
| |
| - | III. Will we be able to take away that awful smoke smell?
| |
| - |
| |
| - | - The removing of the smell is achieved by getting rid of the smell supply and/or sealing the smell source to encapsulate it. Dry ice blasting removes the soot, charcoal and smoke film, which is the smell source, from accessible regions.
| |
| - |
| |
| - | - During a fire air currents carry smoke and soot into cracks, openings and places not in close proximity to the fire itself, additional cleaning and/or sealing of these locations and inaccessible places may be required.
| |
| - |
| |
| - | IV. Can we accomplish our cleanup without having adding hazards to our atmosphere?
| |
| - |
| |
| - | - Dry ice blasting is protected and environmentally friendly. Dry ice is pure CO2 in its solid state, it is in its gaseous state in the air around us. When we inhale our bodies use the oxygen and we exhale CO2. Green plants take CO2 from the air and give off oxygen.
| |
| - |
| |
| - | - Dry ice blasting is non-toxic, non-conductive and there is no employee exposure to hazardous cleaning chemicals or solutions. Dry ice blasting meets the guidelines of the USDA, EPA, and the FDA. You have had a fire. The fire division has come, place the fire out and all you see is one huge mess. Upon closer investigation questions come.
| |
| - |
| |
| - | I. What method do we use to eliminate the soot and charcoal to evaluate the damage?
| |
| - |
| |
| - | - High pressure water blasting leaves behind water in electrical components, gear and insulation, if not properly removed will trigger unwanted corrosion and rot, escalating cleanup, damage and lengthy term maintenance expenses.
| |
| - |
| |
| - | - Soda blasting leaves water and soda behind, which demands added cleanup, escalating cleanup, harm and long phrase upkeep expenses.
| |
| - |
| |
| - | - Sand blasting leaves abrasive blast media behind, which if not cleaned up correctly continues to lead to harm in electrical components, gears and bearings. It continues to fall from horizontal surfaces, cracks and beams years immediately after the job is accomplished, growing cleanup, harm and long term
| |
| - |
| |
| - | upkeep costs.
| |
| - |
| |
| - | - Dry ice blasting is the ultimate surface cleaning process, it leaves no secondary waste stream behind. The only cleanup after the dry ice blasting job is carried out is the removal of the debris brought on by the fire.
| |
| - |
| |
| - | II. How do we get rid of the soot, charcoal and smoke film from masonry and steel surfaces?
| |
| - |
| |
| - | - Again this is an outstanding application for dry ice blasting. Watch the movie clips on our net website to see how dry ice blasting cleans soot, smoke and charcoal from distinct types of surfaces.
| |
| - |
| |
| - | III. Will we be in a position to take away that awful smoke smell?
| |
| - |
| |
| - | - The removing of the smell is achieved by removing the smell source and/or sealing the smell source to encapsulate it. Dry ice blasting removes the soot, charcoal and smoke film, which is the smell supply, from accessible areas.
| |
| - |
| |
| - | - For the duration of a fire air currents carry smoke and soot into cracks, openings and places not in close proximity to the fire itself, additional cleaning and/or sealing of these places and inaccessible areas might be required.
| |
| - |
| |
| - | IV. Can we achieve our cleanup with no adding hazards to our atmosphere?
| |
| - |
| |
| - | - Dry ice blasting is safe and environmentally friendly. Dry ice is pure CO2 in its solid state, it is in its gaseous state in the air around us. When we inhale our bodies use the oxygen and we exhale CO2. Green plants take CO2 from the air and give off oxygen.
| |
| - |
| |
| - | - Dry ice blasting is non-toxic, non-conductive and there is no employee exposure to hazardous cleaning chemical compounds or solutions. Dry ice blasting meets the guidelines of the USDA, EPA, and the FDA.
| |
