From Mycomputer Notes

Revision as of 00:28, 28 April 2006 (edit) 198.168.103.254 (Talk) (→Finishing the Configuration=) ← Previous diff		Revision as of 00:32, 28 April 2006 (edit) (undo) 198.168.103.254 (Talk) (→Finishing the Configuration) Next diff →
Line 105:		Line 105:
	=Finishing the Configuration=		=Finishing the Configuration=
	Best Practice procedures when finalyzing a router's configuration.		Best Practice procedures when finalyzing a router's configuration.
-	*Established configuration standards	+	*
		+	<UL>
		+	<LI>Established configuration standards
		+	The standards procedures should be official and widely used by everyone to avoid chaos
		+	if there is a network failure.
	*Provide and configured interface descriptions		*Provide and configured interface descriptions
	*Configure login banners		*Configure login banners

---

Revision as of 00:32, 28 April 2006

All CLI configuration changes to a Cisco router are made from global configuration mode, which is sometimes called global config. Global config is the primary configuration mode.

Contents 1 Configuring a Router 1.1 Configuring router passwords 1.1.1 Console Password 1.1.2 Virtual Terminal Password 1.1.3 Enable Password 1.1.4 Password encryption 1.2 Configuring Serial & Ethernet Interfaces 2 Finishing the Configuration

Configuring a Router

A router should be given a unique name as one of the first configuration tasks In order to accomplished this go to the global configuration mode with the following command:

Router(config)#hostname Tokyo Tokyo(config)#

Configuring router passwords

As a best practive restrict access to routers with a password. Passwords should always be configured for virtual terminal (vty) lines and the console line. Passwords are also used to control access to privileged EXEC mode so that only authorized users may make changes to the configuration file.

Console Password

Router(Config)# line console 0
Router(Config)# password cisco
Router(Config)# login

Virtual Terminal Password

Router(Config)# line vty 0 4 (when configuring telenet sessions)
Router(Config)# password cisco
Router(Config)# login

Enable Password

Router(Config)# enable password SanFranciso
Router(Config)# service password-encryption (to encrypt non  encrypted passwords)

The enable password used to restrict access to the privileged EXEC mode IF the enable secret has not been set.

Sometimes it is undesirable for passwords to be shown in clear text in the output from the show running-config or show startup-config commands and a a best practice we should used the "service password-encryption" command

Password encryption

Router(Config)# enable secret <password> (encrypted password)

The enable secret commands is used to restrict access to the privileged EXEC mode The enable secret command should be used because the enable secret command is encrypted

Configuring Serial & Ethernet Interfaces

To configure a Serial Interface either from the console or through a virtual terminal line follow these steps:

1. Enter global configuration mode
2. Enter interface mode.
3. Specify the interface address and subnet mask.
4. Set clock rate if a DCE cable is connected. Skip this step if a DTE cable is connected.
5. Turn on the interface.

The variable "TYPE" here is for serial, ethernet, fasethernet, token ring and others.

Router(Config)# interface type port
Router(Config)# interface type slot/port

Each Interface that has been configured with the above commands needs an IP Address and a Subnet mask. Configure the IP address with the following commands:

Router(config)#interface serial 0/0 
Router(config-if)#ip address <ip address > <netmask > 

Serial interfaces require a clock signal to control the timing of the communications in most cases a DCE device such as a CSU/DSU will provide the clock. By default, Cisco routers are DTE devices but they can be configured as DCE devices.

The clock is enabled and speed is specified with the clock rate command. Available clock rates are:

• 1200
• 2400
• 9600
• 19200
• 38400
• 56000
• 64000
• 72000

Some bit rates might not be available on certain serial interfaces. This depends on the capacity of each interface.

This commands is used to administratively turn off/on an interface Command A will administratively turn off an interface Command A will administratively turn on an interface

A) Router(Config)#shutdown
B) Router(Config)# no shutdown

By default, interfaces are turned off, or disabled. To turn on or enable an interface, the command no shutdown is entered. If an interface needs to be administratively disabled for maintenance or troubleshooting, the shutdown command used to turn off the interface.

The commands that are used to set a clock rate and enable a serial interface are as follows:

Router(config)#interface serial 0/0 
Router(config-if)#clock rate 56000 
Router(config-if)#no shutdown

To configure a Ethernet Interface either from the console or through a virtual terminal line follow these steps:

1. Enter global configuration mode.
2. Enter interface configuration mode.
3. Specify the interface address and subnet mask.
4. Enable the interface.

Finishing the Configuration

Best Practice procedures when finalyzing a router's configuration.

• Established configuration standards The standards procedures should be official and widely used by everyone to avoid chaos if there is a network failure.
  • Provide and configured interface descriptions
  • Configure login banners
  • Configuring a message of the day (MOTD) banner
  • Performing host name resolution
  • Performing configuration backup and documentation.